ANTI-FLASH-BUG MODULE H7 - SPEC -AL2 - Car
This anti-error & flash module, specification "AL2", has been specially designed to eliminate flashes and errors that appear during bulb testing at startup on German vehicles. It absorbs flashes and flickering thanks to a 10,000 µF capacitor and eliminates errors thanks to a Smart System, especially on BMW, Mercedes, Audi, Jeep and the VW group. The decoder is designed to reproduce an electrical frequency similar to the cold start of halogen lamps, in order to provide a correct signal feedback loop for the onboard computer. The AGM Vision "AL2" decoder can solve more than 95% of problems related to electrical signals. However, it does not correct certain types of errors, especially those related to low consumption and if you notice persistent flashes, please choose our DL2 module which is better for this, provided your vehicle is not German.
In some cases, it may be necessary to add an additional module, such as this one: 1st Gen H7 Anti-error Module, to increase electrical consumption and completely eliminate the causes that can trigger an error warning.
Please note: it is necessary to purchase one module per LED bulb.
⚠️ Special warning: our module may not work properly and may not provide any result if your LEDs are not from the AGM Vision brand. Please contact us before your purchase to check compatibility.
Satisfaction guaranteed!
Comfort and safety
The module « Anti-Flash-Bug » OBD H7 is based on the latest technologies. Better than any other, this H7 digital filter module is the most effective for reducing flashes at startup (German car) as well as while driving. Ultimate weapon for « operating bugs », such as: LED bulbs that turn off after several minutes or high beam mode that does not work properly. Regarding the treatment and removal of OBD errors, this H7 module Ultra does not use high resistances (adds only +/- 5W of consumption) and therefore cannot compensate for too low electrical consumption. If you are looking to remove an error due to too low electrical consumption, in that case, please choose the Can-Pro H7 or Supreme H7 module instead.
The anti-error module Anti-Flash-Bug H7 works with a filter system controlled by a « Smart Program » coupled with capacitors and resistors. This allows optimal control of errors as well as stability of your vehicle’s electronics, notably by acting on voltage smoothing and on the distribution of electrical load. A very safe anti-error module that creates no heating of wires and terminals nor even any disturbance with your electrical system. Moreover this one has a powerful latest-generation anti-interference filter that will allow you to listen to the radio without crackling in the speakers.
Innovative
The anti-error module Anti-Flash-Bug H7 introduces an all-new system with a capacitor of 10000 uf capacity, thus allowing to reduce flashes, flickering and other blinking from 80% to 100% during the vehicle start-up phases after installing an LED bulb, especially on German vehicles: BMW, MINI, VW, AUDI… Equipped with a (Check control) monitoring system that checks the proper functioning of the bulbs when the vehicle is switched on. The test can last several seconds and is often very noticeable after installing LEDs, creating the appearance of light flashes. If you notice this, use this Anti-Flash-Bug H7 module.
Advantages of the Anti-Flash-Bug module:
• Plug & play installation: plug the module directly between your H7 LED bulb and the vehicle's original H7 socket (can be added with other anti-error modules such as, for example, the Can-Pro H7 module).
• Reduces flashes, flickering and shimmering by 80% to 100% after installing LED bulbs as well as during startup phases, especially on German vehicles (BMW, Mini, VW, AUDI…).
• Restores normal operation of your lighting in most cases: when the high beam mode does not work correctly, when only one out of two LEDs lights up just after installation or when an LED bulb turns off while driving.
• Removes error messages (very effective for errors related to operating bugs and electrical instability). Warning: this Anti-Flash-Bug module will not resolve errors related to too low power consumption. In this case, please add a Can-PRO H7 module in addition to this one.
• Removes radio interference.
• Low heat emission: in fact, thanks to its 100% aluminum shell and internal design, this Anti-Flash-Bug module heats up much less than a classic anti-error module.
• Extends the lifespan of your LED bulbs.